Shimadzu ELB300 Instrukcja Obsługi

SHIMADZU ELECTRONIC BALANCEEL SERIESEL120, EL200, EL300, EL600,EL1200, EL2000, EL3000, EL12K,EL600S, EL6000SINSTRUCTION MANUALM054-E109TESTING &

- 5 -Observe thefollowing:Use only the AC adapter that is provided by thedistributor who is authorized by ShimadzuCorporation.Make sure that any forei

- 6 -(7)The all segments illuminate forapproximately 6 seconds.is displayed.Press the [BREAK] key.Zero is displayed.The zero may be unstable immediate

- 7 -Procedure(1)Press the [MODE] key.The currently set conditions are displayed in symbols.(Example)The display changes in the order shown in the tab

- 8 -required for output. (Be acknowledged that measurementaccuracy may be sacrificed.)• Activating Zero Tracking ( ) will automatically cancelthe min

- 9 -6. Registration of UnitsThree units can be registered in addition to “gram”. The registered units remainafter the power has been turned off. Regi

- 10 -With nothing on the pan, go throughthe menu selections to display for calibration. (Refer to “5. MenuSelection”.)Press the [TARE] key.The value

- 11 -Zero flashes on the display.Remove the weight from the panand press the [TARE] key when thestability mark is displayed.appears on the display an

- 12 -Select piece counting mode (ConvPCS) in menu selection, and pressthe [TARE] key. (Refer to “5. MenuSelection”.)The number of reference pieces i

- 13 -Place the container on the pan and press the [TARE] key.Select percentage conversion mode( %) in menu selection, andpress the [TARE] key. (Refer

- 14 -Procedure(1)increment, is displayedand the display reverts to the unitbefore menu selection.• Press the [BREAK] key to abortpiece counting setti

SHIMADZU ELECTRONIC BALANCEEL SERIESEL120, EL200, EL300, EL600, EL1200, EL2000, EL3000, EL12K,EL600S, EL6000SINSTRUCTION MANUALM054-E084TESTING &

- 15 -The internal values of the balance are beingrevised while is displayed. Do not turnoff the power while is displayed.Press the [TARE] key when

- 16 -while the results are being displayed. (Continuous output isnot possible during specific gravity measurement.)• Return to step (3) by pressing t

- 17 -Preparationfor the [UNIT] key, the value will be calculated and displayedusing the latest reference.• The registered units remain after the powe

- 18 -Both σx and σy should be within 1.5 times the standarddeviation indicated in “15. Specifications”.Load a weight of approximately 1/4th the weigh

- 19 -Wipe any dirt away with a soft cloth moistenedwith a neutral detergent.Organic solvents and chemical dusters willdamage the coating and membrane

- 20 -When Phenomenon Cause and Solution• Affection of vibration or wind.⇒ Install the balance at a place withoutvibration or wind.⇒ Set the response

- 21 -15. SpecificationsModel EL120 EL200 EL300 EL600 EL1200Weighing capacity 120g 200g 300g 600g 1200gMinimum display 0.01g 0.01g 0.01g 0.05g 0.1gSta

- 22 -Model EL2000 EL3000 EL12K EL600S EL6000SWeighing capacity 2000g 3000g 12kg 600g 6000gMinimum display 0.1g 0.1g 1g 0.1g 1gStandard deviation σ ≤

- 23 -16. Parts ListProduct Name P/N RemarksBuilt-in battery 321-60063Below-balance weighing hook 321-34532-03 Cannot be used with the EL12K.Specific

- 24 -Caution andNotesWhen using the battery for the first time, orwhen using it after it has not been used for along period of time, recharge it befo

Follow the cautions below for safe and proper use of the EL balance.Do not use the EL balance in dangerous areas∗.Use only the AC adapter that is prov

- 25 -(3)Fix the sponge (14), battery (15), and holder plate (16) into thebattery compartment and fix them using the fixing screws (17).Ensure that bo

- 26 -Rechargingthe batterySet the power switch to “OFF”. Insert the AC adapter plug intothe power jack of the balance, and insert the AC adapter into

- 27 -ConnectionAfter confirming that the power of the balance has been turnedoff, insert the plug of the IFB-102A into the DATA I/O connector ofthe b

- 28 -Command code + (CR) ⇒ See “18.4 Command Codes”.• When displaying the weightS −△△300.00g△ (CR)Unit + spaceSpace, number, decimal pointPolarity Po

- 29 -• Stop bit Select from 1 and 2.Set the baud rate to 1200 and the stop bit to 1when using the EP-60A.Press the [MODE] key to display(see “5. Menu

- 30 -(6)The currently selected parity is displayed with the stabilitymark.Select the desired parity and press the [TARE] key.∗ The data length become

- 31 -Command code Function DescriptionQ Start operation Switches the display from to weightwhen the power is turned on.Stops Auto Print and continuo

TOKYO OFFICE3, Kanda-Nishikicho 1-chome, Chiyoda-ku, Tokyo 101-8448, JapanPhone: 81(3)3219-5641 Fax: 81(3)3219-5710Cable Add.:SHIMADZU TOK

Thank you for purchasing the Shimadzu EL Series Electronic Balance. Beforeusing the balance, read this Instruction Manual carefully and store it for r

1. List of Components and Names of Units... 12. Installation ...

The following components (one for each) are contained in thepackage.- 1 -List ofcomponents1. List of Components and Names of UnitsBalance main unit AC

- 2 -Key names and functionsUNIT keyBREAK keyMODE keyTARE keyName of Key FunctionBREAK 1) Changes the display from “oFF” to the weight.2) Discontinu

- 3 -DisplayAuto Print mark:Illuminates when the Auto Printfunction is turned on:Percentage markSpecific gravity measurement markNot applicable depend

- 4 -Power suppyCheck the voltage.Check that the voltage of the power supply meetsthe voltage indicated on the AC adapter.Avoid the following conditio